ติดต่อลงโฆษณา [email protected] หรือโทร. 081-811-1138 หรืออ่านรายละเอียดเพิ่มเติม คลิกที่นี่

ตอบกลับหัวข้อ

ชื่อ:

การตรวจสอบ:: กำลังโหลด...

ข้อความ:: [QUOTE="Ake Burnout, post: 544709, member: 39869"]5e-fte Moster Torque!  Austarletclub say "Little Supra"  For an OEM 5efte CT9 buildheres the spoon feeding list for all  - 4efte rocket cover  - 4efte or 5efhe/fe headwith either 4efte or 5efhe cams (MARGINALLY better)..make sure u keep the shims with whatever cams u useor reshimming may be necessary  - 4efte head gasket5efhe or trd head gaskets are also used (but trd raise compression somewhat)  - 4efte intake manifold5efhe ACIS can be use, but usually requires something to operate it properly  - 5e block  - 4efte pistons or some people shave the 5e pistons (TRIED and PROVEN by MANY),,,in fact some people shave the 4efte pistonsbut then a lot of u guys are afraid to do this,,,,,,,,so stick to the oem 4efte ones then  - 4efte piston rings, if u use 4efte pistons..5e pistons rings if u use 5e psitonsthere is a difference in part numbers,,,,,,,,,but people have been know to use any set with any pistons and they work fine  - 5e rods5efhe preferred for bigger boost,,,,,,,,5efe rods can be used if u dont plan to over do it  - 4e/5e cam gear/wheel...set timing using 5e mark.........and set base timing at 10 degrees.........or as desired, as some may want to retard base timing depending on set up and gas quality  - 4efte injectors at MINIMUM   - 4e/5e oem fuel pressure regualtor or aftermarket unit...run anywhere from 2.3 to 3 bar on initial set up,,,BUT depends again on your set up......tune to suit  - 4e/5e fuel rail  - 5e idler and tensioner pulleys  - 4e/5e crank gear  - 5e tming belt  - 4efte ecu, harness and map sensor at minimum.....the greddy ultimate on the 5e ecu or 4efte ecu is also great for fine tuning...  - 5e crank..some prefer 5efhe crank (stamped 5e) on itwhile others use the 3e marked crank which comes in some 5e blocks  - 5e thrust washers  - 5e flywheel (200mm)or redrilled 4efte flywheel (212mm), again, has been done several times, just make sure you have a competent machinistOR try to get the 5e bolt pattern flywheel that holds the 212mm clutch set up (usually found on some 3E engines)  - 5e clutch and 5e pressure plate OR 4efte clutch and 4efte pressure plate.NOT to be mixed and matched  - 5e/4e oil pump.make sure u get the one that matches what is thereas far as Im aware they are two types  - 4e or 5e oil relief valve  - 4efte oil pick up and 4efte sumpOR 5e oil pick up and 5e sump.to be used together and not in combinationsi.e. choose one and use both units together..note,,,u wouldhave to drill and tap the 5e sump for the oil return  - 5e connecting bearingsmake sure u get the correct sizes---check the back of the used one  - 5e main bearings ---- make sure u get the correct sizes---check the block and crank and do some adding of the numbers or check the back of the used one  - 4efte exhaust manifoldBEWARE a custom unit is preferred as the oem unit is VERY restrictive on the 5e  - 1 ct9 turbo and downpipe with all gaskets ---IF u are going to use the ct9 turbo for a short whilealso, your muffler may need a slight extension as the 5e block is about 10mm taller..else use whatever set up (turbo) u plan to run along with supporting exhaust manifold and downpipe  - 4e/5e water pump and hoses  - 4efte thermostat, housing and sensors  - 4e/5e gearbox/transmission  - 4efte distributor or 5efhe distributor..same basic unit  - 4efte plug wires  - 5e timing covers   - 5e oil/dip stick and housing  - 4efte TMIC----NOT the best idea,,,but would work for ct9 set up..if u already have a FMIC set up,,,use it back   จาก เวป Toyotagtturbo.com ครับ     เพื่อเป็นแนวทาง สำหรับบุคคลอื่น ๆ ที่ไม่ทราบว่าต้องใช้อะไรมั้ง ครับ ในการทำ 5E-FTE[/QUOTE]

เข้าสู่ระบบหรือลงทะเบียน

ตอบกลับหัวข้อ

Sitemap

Website Partner

Socialising

เข้าสู่ระบบหรือลงทะเบียน

ตอบกลับหัวข้อ

การค้นหาที่มีประโยชน์